Coyote Hunting AR15

Preparedness Depot in Acworth, GA

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
So this gun I've been putting together is kind of a strange build.

I actually built the gun around the scope.

I bought a p223 3x9-40 w/ BDC 600 reticle. That's the one with marks for each 100 yards point of impact with 55gr 223 up to 600 yards. Additionally it has nice target turrets for the price. The only problem is that the BDC is calibrated for 3240fps. That's only what you'd generslly see from a 20" barrel, and even then it would need to be a pretty decently charged round, not steel or reloads or cheap fmj.

Well I tried it on a 16" barrel and it was waaay off, even more so with GA arms reloads(not that I bother with that ammo anymore). Well I didn't really feel like selling the scope since I had an extra lower, so I just found a bull barrel upper and had it threaded 5/8x24 so I could attach my Specwar QD mounts, but still leave as much meat on the barrel as possible.

I also removed that atrocious tube/barrel nut that was on it and hand tight pressure.

So here is where she's at now. I still need to pick a stock and handguard (15"). I'm thinking a Magpul PRS or Luth AR MBA-1 for the stock. Anyone have opinions on these or another stock that would be fitting?

I've really been hoping to find a 15" samson evolution keymod at a good price as well. Keymod just so I don't have to worry about the back side of the mounting for the pic rails on other foreends contact the gas block at the tip of the handguard. Anyone else have any handguard ideas? I prefer a factory barrel nut, since I already have one, but obviously others are worth looking at if yall have a recommendation

iw4hlx9.png

10729292_1527101447532039_1198794811_n.jpg
 
  • Like
Reactions: Cobalt 60

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
For a coyote rig I've always preferred a composite and smooth fore end to aluminum. It doesn't get as hot or cold, usually there won't be a requirement to mount too much gear to the fore end (maybe a light if you're hunting at night). It makes a bit less noise going through brush.
It's probably not exactly what you're going for, but I always like to keep my hunting rifles as simple as possible, especially one that is going to be packed around a bit calling from stand to stand.
 

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
For a coyote rig I've always preferred a composite and smooth fore end to aluminum. It doesn't get as hot or cold, usually there won't be a requirement to mount too much gear to the fore end (maybe a light if you're hunting at night). It makes a bit less noise going through brush.
It's probably not exactly what you're going for, but I always like to keep my hunting rifles as simple as possible, especially one that is going to be packed around a bit calling from stand to stand.
This is going to be a bipod-ed rifle and I don't really hunt coyotes from a stand or stalk them, I sit on the porch and drop 200-400 yard shots on them.

That and I want this to double for semi-long range with 223.
 

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
Ah, ok. You should check out the AR set ups for prairie dogs. That's really more in line with the type of shooting you'll be doing. You might get some good ideas from some of those folks.

I can't help out much there either as I mainly shot a Tikka heavy barreled 22-250.
 

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
Ah, ok. You should check out the AR set ups for prairie dogs. That's really more in line with the type of shooting you'll be doing. You might get some good ideas from some of those folks.

I can't help out much there either as I mainly shot a Tikka heavy barreled 22-250.
Oh jeebus, well I actually enjoy a little bullet drop
 

DarthVader

Marksman
Mar 25, 2015
1,175
390
113
Henry County
Zip code
30253
Hey, look into the SLR Lite rail. I built this up for a guy who was competing in a predator tournament a couple months ago. The rail is nice and light, which helps with such a heavy barrel. The owner spec'd out a 16.5" rail, which turned out really nice on the 18" barrel.

ae46dd7bf6cec5c7127380b796f0dfee.jpg
4a6f8df7c7813fc7b43bf8367f482a9d.jpg
 

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
Definately go with a Keymod. I have one on my 300BO and it is nice.