First Reloading Thread!

Preparedness Depot in Acworth, GA

dial1911

Waiting for the flash
Site Supporter
Jul 15, 2015
7,331
27,066
113
Anywhere but here
southeastoutdoors.boards.net
Any of you guys converting your 223 brass to 300? I picked up 5000 pieces of 223 for a great price. Just don't know if it would be better to send it off to a service to have it done.

I'm not... but only because I'm anal about head stamps and I don't want my .300 brass to still have .223/Nato head stamps.

If you search youtube, there are a lot of videos of guys converting the brass using a little Harbor Freight cut off saw and the .300 BLK dies.
 
  • Like
Reactions: Richard P. Musgrove

Buckeye76

Frontiersman
Mar 27, 2015
254
144
63
Georgia
I'm not... but only because I'm anal about head stamps and I don't want my .300 brass to still have .223/Nato head stamps.

If you search youtube, there are a lot of videos of guys converting the brass using a little Harbor Freight cut off saw and the .300 BLK dies.

Yeah, if I do it I'm just going to buy the new trimmer from Dillon. Do they need to be annealed?
 
  • Like
Reactions: Richard P. Musgrove

dial1911

Waiting for the flash
Site Supporter
Jul 15, 2015
7,331
27,066
113
Anywhere but here
southeastoutdoors.boards.net
Yeah, if I do it I'm just going to buy the new trimmer from Dillon. Do they need to be annealed?


Annealing is a "stress reliever"... bending the brass into a new shape can cause stress build up in the metal due to cold working. By heating it up it allows the molecules to "relax" into their new locations. Not required, but it does extend the life of the brass according to some people.

Personally, I think the pressure build up and heat from shooting it does sort of the same thing, but probably not quite as well.

You can anneal it by dipping the neck of the new formed brass in molten lead for a second or two. That's all that is required.
 

dial1911

Waiting for the flash
Site Supporter
Jul 15, 2015
7,331
27,066
113
Anywhere but here
southeastoutdoors.boards.net
If anyone has a good 300gr subsonic (under or at 1000fps) load for 44 magnum, that would be awesome. 17" barrel.

The exterior ballistics book was a bust- didn't list the .44 Mag at all.

However the standard Speer reloading manual does show test data from a .44 Mag in a 18.5" barrel Ruger. There isn't a load that is sub sonic (but this was a 18.5" test barrel). The slowest load they show for a 300 grain bullet is AA1680 at 20.7 grains. They list the muzzle velocity at 1148 FPS. I'm not sure if you can safely reduce that powder charge or not. As a rule, I always go by the book and don't go under or over published numbers.
 
  • Like
Reactions: Richard P. Musgrove

Waterguy

Woodsman
Trusted Trader
Lifetime Supporter
Mar 26, 2015
223
113
113
North Georgia
Zip code
30114
Who's did you buy? I have been looking around.

RCBS makes a good one. There are others, just make sure they have calibration weights and check them often or at least before you use them. Also make sure you allow the scale to "warm up" before calibration and use.
 
  • Like
Reactions: Richard P. Musgrove

Woodstock

Tracker
Jun 29, 2015
529
189
113
Zip code
30012
Made some 38 special rounds with 158 gr cast swc and bullseye. Turn the radio on, get my dies set and the powder charge measure and start cranking on the turret press.
I had let my supply dwindle and had to buy some, wow that price motivated me to make more now.
Unbelievably easy round to load
 

Liberty

nitrocellulose dispenser
Site Supporter
Mar 27, 2015
697
612
113
Ga
Zip code
31901
Made some 38 special rounds with 158 gr cast swc and bullseye. Turn the radio on, get my dies set and the powder charge measure and start cranking on the turret press.
I had let my supply dwindle and had to buy some, wow that price motivated me to make more now.
Unbelievably easy round to load

And no chasing brass all over the place when you shoot them!!! New production Bullseye or old stock?
 
  • Like
Reactions: Richard P. Musgrove

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
The exterior ballistics book was a bust- didn't list the .44 Mag at all.

However the standard Speer reloading manual does show test data from a .44 Mag in a 18.5" barrel Ruger. There isn't a load that is sub sonic (but this was a 18.5" test barrel). The slowest load they show for a 300 grain bullet is AA1680 at 20.7 grains. They list the muzzle velocity at 1148 FPS. I'm not sure if you can safely reduce that powder charge or not. As a rule, I always go by the book and don't go under or over published numbers.
I'll post some quick load screenshots later to get some discussion regarding some proposed loads.
 

Liberty

nitrocellulose dispenser
Site Supporter
Mar 27, 2015
697
612
113
Ga
Zip code
31901
That's for sure, unfortunately that also makes the brass a little hard to find in once fired.
Pretty sure its newer, when did it change?


Just wondering if you found it stittng on a shelf somewhere recently. Would love to have a lb. for my .45
 
  • Like
Reactions: Richard P. Musgrove

LXHunter

Frontiersman
Jun 24, 2015
314
97
93
Zip code
30517
Hard to pay for a reloading setup loading 9. Saving .20c a round on .45 and up to 2.00 a shot on common premium centerfire hunting/ match ammo lowers the cost fast.
I agree. I have never had much luck with reloading 9mm and as cheap as it is I find it easier to buy. I currently load .45acp, .223, and .308. With my shooting habits though I find reloading .45acp is really what I must shoot the most - lol
 
  • Like
Reactions: Richard P. Musgrove