2 piece 9mm AR Bolt?

GA Firing Line

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
I dig it, especially the increased mass. How many pieces is a 5.56 bcg?
 

Cudruln

Turning dollars into pennies.
Lifetime Supporter
Jul 5, 2015
4,337
4,579
113
Rockmart, GA
Zip code
30153
I would be willing to give it a shot. Especially if you have the nfa ar9 lower. Seems to me they would make something that would work with their own products.
 

DarthVader

Marksman
Mar 25, 2015
1,175
390
113
Henry County
Zip code
30253
Thoughts?

9mm New Frontier Armory Modular AR BCG

http://www.joeboboutfitters.com/New...ar_9mm_Bolt_Carrier_p/nfa-ar9-modular-bcg.htm

I immediately hesitated at the thought of a two piece bcg.

@DarthVader?
Not sure why I didn't get a notification on this sooner. I'd like to see one of these on high speed film. It doesn't look like the halves mate together as a single unit. The idea of being able to switch the bolt face out to shoot 40 S&W or 45 ACP is pretty interesting. To me, a caliber change is going to be an upper swap anyway, so why not just run separate, complete upper groups. And you'd have to buy separate bolt heads, so that eats into any cost savings.

But I think the bigger question is one of possible bolt bounce and reliability. The unit would likely travel backwards as a single unit. But I wonder if the the impacts as the carrier hits it's max rear travel would jolt them apart slightly? Or if they would separate as the carrier travels forward and impacts the barrel extension? Often, the forward impact causes a regular AR BCG to bounce backwards slightly before coming to its final position, locked into the extension. This is usually exacerbated with over gassing and high carrier speeds. A heavy buffer or increased power buffer spring can usually tame it. And it is usually only an issue with full auto fire.

Honestly though, is this a solution looking for a problem? It's not often that we see an AR pattern subgun in anything other than 9mm. Or maybe NFA just tipped their hand and intend to expand their offerings to other calibers and complete uppers.
I dig it, especially the increased mass. How many pieces is a 5.56 bcg?
Sort of the same thing, but not really. The bolt is designed for linear movement within an AR carrier, but the 9mm carrier isn't. I guess I'd like to see one run on FA just to see what happens.
 

DarthVader

Marksman
Mar 25, 2015
1,175
390
113
Henry County
Zip code
30253
A couple of good videos demonstrating bolt bounce

I suppose the question is, what would this look like if the carrier were two separate reciprocating parts?


 

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
Not sure why I didn't get a notification on this sooner. I'd like to see one of these on high speed film. It doesn't look like the halves mate together as a single unit. The idea of being able to switch the bolt face out to shoot 40 S&W or 45 ACP is pretty interesting. To me, a caliber change is going to be an upper swap anyway, so why not just run separate, complete upper groups. And you'd have to buy separate bolt heads, so that eats into any cost savings.

But I think the bigger question is one of possible bolt bounce and reliability. The unit would likely travel backwards as a single unit. But I wonder if the the impacts as the carrier hits it's max rear travel would jolt them apart slightly? Or if they would separate as the carrier travels forward and impacts the barrel extension? Often, the forward impact causes a regular AR BCG to bounce backwards slightly before coming to its final position, locked into the extension. This is usually exacerbated with over gassing and high carrier speeds. A heavy buffer or increased power buffer spring can usually tame it. And it is usually only an issue with full auto fire.

Honestly though, is this a solution looking for a problem? It's not often that we see an AR pattern subgun in anything other than 9mm. Or maybe NFA just tipped their hand and intend to expand their offerings to other calibers and complete uppers.

Sort of the same thing, but not really. The bolt is designed for linear movement within an AR carrier, but the 9mm carrier isn't. I guess I'd like to see one run on FA just to see what happens.



Oh I don't really care one way or the other, I was just being disagreeable with @rOmiLaYu for the sake of being disagreeable.
 
  • Like
Reactions: DarthVader

DarthVader

Marksman
Mar 25, 2015
1,175
390
113
Henry County
Zip code
30253
LOL!

PS: I know you know the difference. Didn't mean for that to sound like I was pontificating in response to you. But I am curious what you think about it.
 
Last edited:

rOmiLaYu

Tracker
Trusted Trader
Mar 25, 2015
656
262
113
Earth
Zip code
30132
It doesn't look like the halves mate together as a single unit.
It doesn't look that way to me either...which makes me wonder about...

bolt bounce and reliability.
and....

Honestly though, is this a solution looking for a problem? It's not often that we see an AR pattern subgun in anything other than 9mm. Or maybe NFA just tipped their hand and intend to expand their offerings to other calibers and complete uppers
Yup, had that thought, too. Actually, I had exactly the same thoughts you did.

I think I'll pass.
 
  • Like
Reactions: DarthVader

Willy Leadwell

Purveyor of Polyurethane
Lifetime Supporter
Mar 26, 2015
2,159
1,679
113
Loganville, GA
Zip code
30052
I haven't seen one thing that would indicate to me that I should own one of these. I don't even get what purpose it's supposed to serve.
 

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
I haven't seen one thing that would indicate to me that I should own one of these. I don't even get what purpose it's supposed to serve.
9mm AR's are stupid fun to suppress. and with NFA arms new glock lower and glock cut bolt its a great time to jump in at a low price.
 

DarthVader

Marksman
Mar 25, 2015
1,175
390
113
Henry County
Zip code
30253
I haven't seen one thing that would indicate to me that I should own one of these. I don't even get what purpose it's supposed to serve.
The only advantage I see, assuming that it doesn't create any reliability issues, is that you can easily swap the bolt face for other calibers. And if they were so inclined, they could offer different weight carrier tails. But someone would need to offer uppers in other calibers for any of that to matter.
 

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
9mm AR's are stupid fun to suppress. and with NFA arms new glock lower and glock cut bolt its a great time to jump in at a low price.


Yeah, kinda pissed all this came out right after I dumped all the money on a Hahn block and 9mm upper.
 

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
I have a suppressed 9mm SBR. I still don't understand how this bolt helps me.


If you didn't have one, it is a cheaper alternative than what was already on the market plus apparently it has increased mass and the ability to change calibers down the road.
 

Willy Leadwell

Purveyor of Polyurethane
Lifetime Supporter
Mar 26, 2015
2,159
1,679
113
Loganville, GA
Zip code
30052
The only advantage I see, assuming that it doesn't create any reliability issues, is that you can easily swap the bolt face for other calibers. And if they were so inclined, they could offer different weight carrier tails. But someone would need to offer uppers in other calibers for any of that to matter.
so what you're saying is that they've found a complicated way to simplify things a bit?
 

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
The only advantage I see, assuming that it doesn't create any reliability issues, is that you can easily swap the bolt face for other calibers. And if they were so inclined, they could offer different weight carrier tails. But someone would need to offer uppers in other calibers for any of that to matter.
Qcircle10 sells 40, 10mm, and 357 sig uppers

I believe their 45 upper is on its way out soon as well if not already out
 

Willy Leadwell

Purveyor of Polyurethane
Lifetime Supporter
Mar 26, 2015
2,159
1,679
113
Loganville, GA
Zip code
30052
If you didn't have one, it is a cheaper alternative than what was already on the market plus apparently it has increased mass and the ability to change calibers down the road.
So it's super easy to change the bolt, but I still have to change the barrel, or have multiple uppers that share a bolt?