DIY GasBuster Charging Handle.

Preparedness Depot in Acworth, GA

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
I am sure we are all familiar with the PRI Gas Buster Charging Handle. It is a charging handle with a radius cut in the bottom that diverts excess gas out the right side to prevent gases from reaching the shooters face. They work well, but truth be told they run just under 100 bucks which is a lot of coin to spend on a charging handle.

Screen%20Shot%202015-07-29%20at%209.36.32%20AM_zpswpnbh6qo.png


To build my own I locked up a standard charging handle in my vice and marked a point of reference for where I wanted to drill the hole. I intended to drill two holes that intersect as seen in the following picture, but I lucked out and only needed one hole. The charging handle creates a natural radius at my hole so I think this worked out really well.

Planned holes.
ar15chmod03.jpg


Here my charging handle is in the vice.

uyfc.jpg


Because the charging handle is aluminum the drilling was VERY easy. I used a 5/32″ drill. Go slow to prevent yourself from drilling too far through the charging handle. Here the hole I drilled is with the drill still inside for reference.
8h8b.jpg


Next I cleaned up the hole with a chainsaw file just to make it look original and hit it with a shot of Brownells Aluma Black. I wiped the excess paint off with a shop rag immediately so the only place the paint remained was inside the hole I drilled.

ssyy.jpg


Here the charging handle is on the gun.
6ml6.jpg


Now excess gas will be diverted out the right side of the charging handle instead of into the shooters face. This is really important on SBRs, Pistols, or shooting suppressed.

You can also fill the gap on the top back of the charging handle with RTV sealant and allow to dry overnight as seen in the following picture. This will prevent any stray gas from getting out the back of the charging handle.
DPP_0003copy%5b1%5d.jpg


Full instructions on the RTV sealant can be found at the following URL. I would have completed this step today but I don’t have any RTV and honestly I believe the drilled hole with achieve better results.

http://www.03designgroup.com/technotes/do-it-yourself-gas-buster-charging-handle

Honestly I am so happy with the results of the drilled hole, I am contemplating drilling all my charging handles in the same fashion.
 
  • Like
Reactions: Laufen

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
Nice write up. I think I'll do that this weekend on my peasant guns.
 

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
hmmm. I don't know if that would be what I would call a peasant gun, but cool I guess.
I don't know how much difference it'll make on a 16" un-supressed carbine, but we'll find out.
 

chance

Tracker
Jul 15, 2015
958
1,073
113
Ga
Zip code
30101
Might have to try this. I could do the radius cut in the mill too.

Need to figure out a way to do something similar to my 551 SBR too. Its a bit gassy, even with a modified gas valve
 

freedom

Sniper
Mar 25, 2015
1,522
885
113
Covington, Ga
Zip code
30014
Is there anything someone that shoots left handed could do to mitigate the gas?

I choke on it shooting a 12" supressed rifle.
 

Hayata

Blam-blam-blam-blam-blam-blam-blam-blam-PING!
Kalash Klub
Lifetime Supporter
Jul 5, 2015
6,135
30,134
113
Zip code
30022
I love these kind of DIY threads!