Who Can Pin FSB on My Barrel

[Red Dawn]

Is there a local shop that will pin an FSB to my barrel. Does anybody have a suggestion. Thanks

 

[boss_hawg]

what's your location?

 

[Red Dawn]

Henry County

 

[EugenFJR]

How close is @FatAlbert to you? I was very pleased with his work, when I sent him some stuff to be painted. I had my A2 flash hider pinned at Nonliberals place, but he is just around the corner from me.

 

[permaneo vox]

Let me look & see if I can find my 0 reamer, if so, I can do taper pins. Straight pins, well, I may not have the correct reamer.

 

[Rwjeter]

How close is @FatAlbert to you? I was very pleased with his work, when I sent him some stuff to be painted. I had my A2 flash hider pinned at Nonliberals place, but he is just around the corner from me.

How much did he charge you? I might take my 9mm up there and just have the sight pinned. I'm not having much luck finding a clamp on I like.

 

[Red Dawn]

How close is @FatAlbert to you? I was very pleased with his work, when I sent him some stuff to be painted. I had my A2 flash hider pinned at Nonliberals place, but he is just around the corner from me.

Thanks he's not too far

 

[Red Dawn]

Let me look & see if I can find my 0 reamer, if so, I can do taper pins. Straight pins, well, I may not have the correct reamer.

Thanks for checking

 

[dial1911]

Six hours goes by and not one post mentions "duct tape"...

 

[FatAlbert]

How close is @FatAlbert to you? I was very pleased with his work, when I sent him some stuff to be painted. I had my A2 flash hider pinned at Nonliberals place, but he is just around the corner from me.

I don't have the tools to do a proper job pinning a FSB. I hope to get more machining equipment in the future but for now I pretty much just Cerakote and do very basic Gunsmithing. I'm pretty much just a parts replacer for now.

Just buying the tools to correctly disassemble and reassemble all different kinds of firearms will break a man haha. Next on my list is bluing tanks. After that I'll start looking into lathes and a small mill so I can start doing some real Gunsmithing.

 

[permaneo vox]

Six hours goes by and not one post mentions "duct tape"...

Actually, green Loktite bearing mount. It wont move.

 

[freedom]

You need to be willing to ship it off to get this done.

Is buying a barrel with it installed not an option? I think your looking at $75-100 to get this done. If possible, I'd sell what you have and buy what you want.

 

[permaneo vox]

Your lookingat $35-40 to get it done. Its a half hours work including set up.

 

[Red Dawn]

I want to buy a 18" barrel and put an F Mark FSB on it to go with the detach carry handle. That's the plan at least for now.

 

[fyroc]

I want to buy a 18" barrel and put an F Mark FSB on it to go with the detach carry handle. That's the plan at least for now.

18'? Why do you need to pin it then?

 

[Red Dawn]

18'? Why do you need to pin it then?

That's the best gb for not leaking or moving and I thought for sites to line up and zero on the carry handle I needed F marked FSB

 

[fyroc]

That's the best gb for not leaking or moving and I thought for sites to line up and zero on the carry handle I needed F marked FSB

Oh shit the FSB... I thought you meant muzzle device. I did one with a hand drill and a puckered asshole.

 

[Red Dawn]

I don't know if there will be issues or not cycling rifle buffer I've heard some people had to put lighter buffers with some barrels being made today

 

[fyroc]

I don't know if there will be issues or not cycling rifle buffer I've heard some people had to put lighter buffers with some barrels being made today

What barrel are you using? My 18" Mega SPR barrel cycles my rifle buffer just fine.

 

[Red Dawn]

What barrel are you using? My 18" Mega SPR barrel cycles my rifle buffer just fine.

I'm still searching because the only 18" pinned option I found is
Faxon



I'd like 1/7 556 rifle gas and .750 block at that price range