D
Denny4kids
Guest
Item reviewed: Fulton Armory top loading single-shot magazine follower designed to fit an aluminum or steel AR-15/M-16 magazine. This device allows the shooter to load a longer than magazine length round in his/her AR-15 and shoot the weapon as a single shot rifle.
The follower was delivered with an allen wrench installation tool and well written instructions and clear illustrations. I placed the allen wrench into a small hole on the plastic follower and rolled it into position over the existing follower. Piece of cake. It also pops right back out with ease.
I headed out to the range with my Stag 3g 1-8 twist and 40 75 grain A-maxes pushed by CFE 223 powder. The wind was blowing pretty hard. The flags were fully extended from left to right.
My method for shooting was right handed with the aid of a bipod. Safety on, steady weapon with support hand and with the bolt open, just place a round in the ejection port. I would then hit the bolt release, acquire target, remove safety, aim and fire. The bolt stays open after each shot.
No matter how I tossed in a cartridge it would fall into the proper position to chamber. No special care was needed. I also brought a mic. to check the COL and nothing changed after chambering a round. I haven't had this weapon for long and these are the most accurate rounds I have fired. This old Man shot a half inch 5 shot group at 100 yards with ease.
Pros: Easy to use, the thing works perfect
Cons: none found
Best uses: allows AR-15 shooter to operate his/her carbine as a single shot weapon to shoot a slightly longer than magazine length round or to train a new shooter using standard ammo.
I used this mag follower for 40 rounds, no wear detected.
Item was purchased on ebay for $12 delivered. Took 4 days to receive. Pretty good!
http://www.ebay.com/itm/AR-223-Single-Shot-Magazine-Follower-Snaps-in-Top-of-Magazine-in-Seconds-/151028946941?ssPageName=ADME:L:OC:US:3160
I must rate this item a 5 out of 5 and the seller is a 5 also. Denny
The follower was delivered with an allen wrench installation tool and well written instructions and clear illustrations. I placed the allen wrench into a small hole on the plastic follower and rolled it into position over the existing follower. Piece of cake. It also pops right back out with ease.
I headed out to the range with my Stag 3g 1-8 twist and 40 75 grain A-maxes pushed by CFE 223 powder. The wind was blowing pretty hard. The flags were fully extended from left to right.
My method for shooting was right handed with the aid of a bipod. Safety on, steady weapon with support hand and with the bolt open, just place a round in the ejection port. I would then hit the bolt release, acquire target, remove safety, aim and fire. The bolt stays open after each shot.
No matter how I tossed in a cartridge it would fall into the proper position to chamber. No special care was needed. I also brought a mic. to check the COL and nothing changed after chambering a round. I haven't had this weapon for long and these are the most accurate rounds I have fired. This old Man shot a half inch 5 shot group at 100 yards with ease.
Pros: Easy to use, the thing works perfect
Cons: none found
Best uses: allows AR-15 shooter to operate his/her carbine as a single shot weapon to shoot a slightly longer than magazine length round or to train a new shooter using standard ammo.
I used this mag follower for 40 rounds, no wear detected.
Item was purchased on ebay for $12 delivered. Took 4 days to receive. Pretty good!
http://www.ebay.com/itm/AR-223-Single-Shot-Magazine-Follower-Snaps-in-Top-of-Magazine-in-Seconds-/151028946941?ssPageName=ADME:L:OC:US:3160
I must rate this item a 5 out of 5 and the seller is a 5 also. Denny
