Public toilets?

[Rabbit2047]

Yeah the angle of the MI Mlok rail for the Galil Ace isn’t as extreme as AR rails for whatever reason. So I haven’t tried, but it doesn’t look angled enough to put an offset on. I can/may use the middle section of Mlok to mount my perst on the side but the emitter is on the bottom of the designator so that will put the laser even more below bore.

I always go for a parallel zero so all my lasers are slightly offset from bore. Like my top mounted LS321G is really about 1” higher and 1” to the right of bore, but parallel zeroed to the bore will put impact 1” low and 1” left on target to pretty much infinity.

If I could get a section of rail mounted on the side, not the angles but lifted another inch up on the rail the emitter would almost be inline with bore and just an inch or so right so my elevation would true and Impact would just be offset to the left on the target

View attachment 96980 View attachment 96981

If I feel up to it tomorrow I will play around in my scrap bin and see what I can fabricate.

 

[Axeman]

Free hookers

You mean frozen hookers?

 

[Axeman]

see if the back of the mag underneath the lug is hitting the front of the safety stop at the magwell

Not sure what the ‘safety stop’ is

 

[EugenFJR]

I may just have to live with a slight impact offset with elevation and wind age like I typically do. Just gotta remember the rounds hit up and left on the Galil and low and left on the geiselle lol

Or mount that bitch on the top like I usually do anyways and put the MRO on a slight riser to get it a bit above the designator

Zeroing a lazer is always a pain in the ass. That being said, I need to get a set up for my primary rifle...

 

[Rabbit2047]

Not sure what the ‘safety stop’ is

The plate between the trigger guard and the receiver.

 

[AC-130 Above]

always wanted one of these when I was a kid

Maruzen Model Vz61 Scorpion gas blowback air soft made in Japan | eBay

THIS REPLICA AIRSOFT GUN CONTAINS THE COLORED MARKINGS REQUIRED BY LAW INCLUDING A PERMANENTLY ATTACHED ORANGE PLUG.MUST BE 18 YEARS OLD TO BUY.NO SALES OUTSIDE OF THE USA.

www.ebay.com

 

[Rabbit2047]

 

[YUK0N]

See if y’all know any secrets

Looking for an mlok attachment like this, but With Picatinny instead of the two holes on the top used to mount a scout light. Like if you were wanting to raise/lift a section of pic higher than the Mlok slot you’re locking into.

View attachment 96976 View attachment 96977

I think haley strategic makes a mount you are looking for ( i think )


Sent from my iPhone using Tapatalk

 

[YUK0N]

See if y’all know any secrets

Looking for an mlok attachment like this, but With Picatinny instead of the two holes on the top used to mount a scout light. Like if you were wanting to raise/lift a section of pic higher than the Mlok slot you’re locking into.

View attachment 96976 View attachment 96977

Like this?

Thorntail2 Picatinny Offset Light Mount

Thorntail2 Picatinny Offset Light Mount For use with: all 1913 picatinny rail mounted lights and 1913 picatinny compliant rails Weight: 0.784 oz Material: 6061-T6 aluminum black anodized per mil-spec mil-a-8625 Ambidextrous with 8 total mounting so

haleystrategic.com

Sent from my iPhone using Tapatalk

 

[Rabbit2047]

 

[3clicks_Off]

AK me

 

[Okuma]

Buy my stuff!
06 F150
15 Tacoma
97 Nissan
2 snapper comets
Jeep 4.0 engine(smokes)
Dana 44/Ford 9” axles

 

[lesptr]

View attachment 96965

You seem excited.

 

[lesptr]

Ruger MK IV is my 1st choice. For what's it's worth.

Cleaning on those is so easy.

 

[3x]

I need some cardboard rifle boxes

 

[Abishai]

morning

 

[Fast306stang]

Morning all!

 

[Rabbit2047]

Good morning yall dirty heauxs

 

[Miles]

Buy my stuff!
06 F150
15 Tacoma
97 Nissan
2 snapper comets
Jeep 4.0 engine(smokes)
Dana 44/Ford 9” axles

Trade you 15 Tacoma for 4 cases of 9mm Speer ammo. I know what I got!

 

[Okuma]

Trade you 15 Tacoma for 4 cases of 9mm Speer ammo. I know what I got!

Deal! I’ll even add some cash.