I haven't seen that, but they are going for full retail. I was lucky to get about $2,000 off retail, when I bought my truck in June. But if you have a hard on for a Bronco, then you should expect to pay 5k over MSRP.
Foreign Weapons and Obscure Builds V3
- Thread starter KhyberPass
- Start date
I haven't seen that, but they are going for full retail. I was lucky to get about $2,000 off retail, when I bought my truck in June. But if you have a hard on for a Bronco, then you should expect to pay 5k over MSRP.
- Jul 5, 2015
- 6,135
- 30,134
- 113
- Zip code
- 30022
I was looking at KBB, and that price isn't too far off most asking prices. In this market he would be better off selling it to a dealer. He won't get $8,800 bucks but he might get a check for around $6500.00.
I'd never buy a Chevrolet, much less one with 235k on it.
You might want to contact @DeanMoriarty he has some analyzed ezzzz,
Brock looks like a shark with legs
I just checked my new truck on KBB. They do not have 2022 Tacos in the system yet, so I used 2021.
It is worth $5K more than my OTD cost.
Wow.
Did they let you keep your old gallbladder in a jar? I remember when my dad got his removed.
Hang in there! Prayers sent.
Similar thing with my Mazda. It's crazy.
When it rains, it pours. Glad you got through the real crappy part, so you can focus on getting back up to speed. Still sucks to go through and sucks right now, but there's a lot to look forward to.
Century Paratrooper------
I removed the way too short stupid countersunk allens that Century used in both folder hole locations. The front hole is 10 mm and the rear hole is 8mm. Looks like Century used 5mm in both holes. The rear screw can not be any longer than the hole or it hits when opening and closing the folder. I gots some slot head screws and turned the head down to .300" from the original .350". This looks a lot better as the taper in these screws, or Century's allens, sticks way above the hole when tight. I believe the correct screws may have a different taper, but I am doing what I can with available stuff. Notice also that the Romulan hole is not centered in the tang and the screw was hitting the side so this one is .280"
I removed the way too short stupid countersunk allens that Century used in both folder hole locations. The front hole is 10 mm and the rear hole is 8mm. Looks like Century used 5mm in both holes. The rear screw can not be any longer than the hole or it hits when opening and closing the folder. I gots some slot head screws and turned the head down to .300" from the original .350". This looks a lot better as the taper in these screws, or Century's allens, sticks way above the hole when tight. I believe the correct screws may have a different taper, but I am doing what I can with available stuff. Notice also that the Romulan hole is not centered in the tang and the screw was hitting the side so this one is .280"
Nope. I wouldn't have wanted it anyways.
I sold my 2021 Camry SE that I bought last January for 3k more than I paid 5 months later.
Then bought my All wheel drive Camry XSE at that time.
Car prices are NUTS
@Jake Prayers for speedy recovery.
And I am at hospital now with my wife and she is having Carpal Tunnel surgery as I type this.
Doctor just came in and said everything went great with her surgery and that her carpal tunnel problem was severe.
He said he got everything done and she should be ok now with her right hand.
- Jul 5, 2015
- 6,135
- 30,134
- 113
- Zip code
- 30022