Make a wooden box
- Thread starter dial1911
- Start date
Well, I'm damn sure not there yet. But I think things are improving... thanks!!
nothing a little dap caulk won`t fix.....
Black CA glue.... which is what the youngsters call super glue these days.
I decided to use some orange paduk to make the lid liners. Nice little color pop inside the box.
Lots of finish sanding today.
Also had to make a repair to one corner that popped open. Super glue and activator did an ok job.
Lots of finish sanding today.
Also had to make a repair to one corner that popped open. Super glue and activator did an ok job.
Got a neat surprise coming up....
Anyway, glued a few scraps together to try a handle. I thought they were too small... and i think i was right. Glued 3 full thickness layers together tonight to try again tomorrow.
The mini handle-
I think it's just too small. At least for what i had pictured.
Anyway, glued a few scraps together to try a handle. I thought they were too small... and i think i was right. Glued 3 full thickness layers together tonight to try again tomorrow.
The mini handle-
I think it's just too small. At least for what i had pictured.
I love the way dovetail joints look. I've never tried making any though.
My glue up from last night dried, so off to make some knobs.
A little wood lathe time lapse-
I like how the saw dust keeps building up in those pictures.
A little wood lathe time lapse-
I like how the saw dust keeps building up in those pictures.
Last lathe step is to cut away as much wood as possible between the good pieces-
Then take off machine, hand saw the pieces apart, and do some final sanding. Then, after a few short hours you'll have a few knobs to pick from.
Then take off machine, hand saw the pieces apart, and do some final sanding. Then, after a few short hours you'll have a few knobs to pick from.
No kidding... 9:30 first picture, 12:05 last picture... 2.5 hours (not including over night gluing/ cutting the blanks) for 4 knobs. One of which has a hole in the top because i drilled a little too deep for the lathe center.
Last edited:
Time for finish. I've been using natural color danish oil lately... it's easy to wipe on and looks good. I'll usually just put some finishing wax on top of 2 coats of oil... but i may put on a few coats of poly on this box.
Not much to talk about... wear gloves, cut a piece of old t shirt for the oil, have some q tips for the corners, and make sure you don't miss a spot. I try to watch out for my finger prints and wipe those smooth after i sit the piece down.
Love the first coat of oil...
Not much to talk about... wear gloves, cut a piece of old t shirt for the oil, have some q tips for the corners, and make sure you don't miss a spot. I try to watch out for my finger prints and wipe those smooth after i sit the piece down.
Love the first coat of oil...
First coat dried. Now i like to take a clean piece of t shirt and buff all the surfaces by hand. There always some kind of sticky spots where the oil didn't fully absorb. The buffing takes them right off (so long as you do it a couple hours after putting the oil on... wait overnight and it becomes more like dry bubblegum).
Also found a rough spot or two on the handle. I'll wet sand those with a piece of 220 or 320 grit when i do the second coat later. You can avoid the grain raising up and making rough spots if you mist the wood with water before final sanding (just lightly wet it). That will raise the grain as it dries and you can sand it off then. The light brown areas are a little rough-
Overall, it's coming along pretty good. There are some minor mistakes, but that's always the case. Keep learning, keep practicing, and chase perfection.
Also found a rough spot or two on the handle. I'll wet sand those with a piece of 220 or 320 grit when i do the second coat later. You can avoid the grain raising up and making rough spots if you mist the wood with water before final sanding (just lightly wet it). That will raise the grain as it dries and you can sand it off then. The light brown areas are a little rough-
Overall, it's coming along pretty good. There are some minor mistakes, but that's always the case. Keep learning, keep practicing, and chase perfection.
Almost done. Need to cut a leather piece for the bottom to cover up that plywood.
I mentioned making this more complicated, but cooler earlier. So i gave the bottom a mostly hidden drawer.
I mentioned making this more complicated, but cooler earlier. So i gave the bottom a mostly hidden drawer.
Last edited:
Please figure a price on one of these so I can start scrounging pennies,
I love this!Please figure a price on one of these so I can start scrounging pennies,
Well, the good news is that's only about $30-ish worth of wood.
The bad news is it took working in it from Sunday to Sunday every day.
I did go ahead and put in the leather bottom liner. Honestly, there's no need for a second coat of oil on this one. I will buff it with finishing wax once the oil fully sets.
I don't doubt the time it took. I did some woodworking in the past when my hands would do what I told them to (though I never reached your skill level), so I know it is NEVER as simple as so many people seem to believe.
I'm going to have to plan a trip to the wood store after I'm back up and around. I looked at the walnut i have here and none of it has that crazy grain pattern.
Funny thing is that particular piece of walnut came from a "discount" pile at the wood store. They had a pallet of 6 foot pieces that were only $6 a board foot (normal full length boards are $13/bd. ft. if in remembering right).
That pallet had mostly narrow boards, mostly kinda twisted/ warped, cracked, and generally messed up enough to make you not want to deal with them. But... those twisted, warped pieces had some amazing grain. I bought one to see if i could use it. The best grain patterns come from forks, knots, and generally bad parts of the tree.
Half the board is too crooked to use. But you could cut some of them down, straighten it and have a nice piece. Of course, the other half might be trash, so your back to paying full price (well, $12 /bd ft).
You know, that time estimate wasn't quite fair.
I usually batch process boards because it's much easier to run several pieces once the tools are set up. I looked back through the pictures and made 4 bixes worth of thin pieces, 3 spare knobs, and at least one other box top.
Just guessing, but if i could reuse all those materials (but i can't exactly because the knob material doesn't match most of the board i cut down), but anyway, i could probably turn out at least 2 (maybe 3) boxes this week (surgery aside).
That's not including several details like making knobs. I have several store bought metal drawer pulls intended to be used as knobs. That would speed up production, but it's not the same as a knob made of the same wood.